丙烯腈丁二烯苯乙烯ABS,ABS Hylac® EX18是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123,微信:13549213581 QQ:15397858 13549213581 肖生
ABS超高抗冲击性,挤出
Hylac® EX18
丙烯腈丁二烯苯乙烯
Entec Polymers
Technical Data
产品说明
Hylac® EX18是一种丙烯腈丁二烯苯乙烯(ABS)材料,。 该产品在北美洲有供货,加工方式为:挤出。
Hylac® EX18的主要特性有:
• 通过 ROHS 认证
• 耐冲击
总体
材料状态 • 已商用:当前有效
资料 1 • Technical Datasheet
搜索 UL 黄卡 • Entec Polymers
• Hylac®
供货地区 • 北美洲
特性 • 超高抗冲击性
RoHS 合规性 • RoHS 合规
形式 • 粒子
加工方法 • 挤出
物理性能 额定值单位制 测试方法
比重 1.03g/cm³ ASTM D792
熔流率(熔体流动速率)
200°C/5.0 kg 0.40g/10 min ASTM D1238
220°C/10.0 kg 4.5g/10 min ISO 1133
收缩率 - 流动 0.30 到 0.70% ASTM D955
机械性能 额定值单位制 测试方法
拉伸模量 (23°C) 2310MPa ASTM D638
抗张强度 (屈服, 23°C) 34.5MPa ASTM D638
伸长率 (断裂, 23°C) 40% ASTM D638
弯曲模量 (23°C) 1930MPa ASTM D790
弯曲强度 (屈服, 23°C) 55.2MPa ASTM D790
冲击性能 额定值单位制 测试方法
悬壁梁缺口冲击强度 ASTM D256
23°C, 3.18 mm 430J/m
23°C, 6.35 mm 380J/m
硬度 额定值单位制 测试方法
洛氏硬度 (R 级) 100 ASTM D785
热性能 额定值单位制 测试方法
载荷下热变形温度 ASTM D648
0.45 MPa, 未退火 96.1°C
1.8 MPa, 未退火 86.1°C
维卡软化温度 106°C ASTM D1525
线形热膨胀系数 - 流动 (-40 到 80°C) 1.2E-4cm/cm/°C ASTM D696
电气性能 额定值单位制 测试方法
体积电阻率 1.0E+15ohm·cm ASTM D257
补充信息
Melt Flow Rate, ASTM D1238, 230°C, 3.8kg: 0.8 g/10min
Volume Resistivity, ASTM D257: >10^15
CLTE, ASTM D696, -40°C to 80°C, Annealed: 6.6e-5 in/in/°F
挤出 额定值单位制
干燥温度 85.0°C
干燥时间 3.0hr
Hylac® EX18
丙烯腈丁二烯苯乙烯
Entec Polymers
挤出 额定值单位制
建议的最大水分含量 0.020%
料筒1区温度 191 到 210°C
料筒2区温度 191 到 210°C
料筒3区温度 199 到 221°C
料筒4区温度 199 到 221°C
料筒5区温度 199 到 221°C
接头温度 221 到 241°C
口模温度 221 到 241°C
挤压说明
Hylac ABS extrusion grade resins should be dried to a moisture content of 0.02% or less prior to processing. Control of the outer stock temperature is important in successfully finishing the product. Typical temperatures of outer stock range from 160°F to 175°F after passing through a water bath. The bath temperature profile will greatly affect the dimensional stability and appearance of the part, and if not set up properly could be detrimental to the ultimate mechanical strength of the product. Extruders with one-stage or two-stage force venting are recommended for the extrusion of sheets or profiles. Compression ratios should be between 2.5/1 and 3.0/1 for a single screw and between 1.5/1 and .0/1 for a two-stage screw. L/D ratios of 20/1 and 36/1 are typical.
Process Parameter:
Zone 6: 430-465°F
Zone 7: 430-465°F
Outer Die Zone: 435-475°F
Mid Die Zone: 430-465°F
Center Die Zone: 420-465°F Die Lip Thickness: 3.2-4.0 mm Nip Roll Top: 185-195°F
Nip Roll Middle: 175-185°F
Nip Roll Bottom: 165-175°F
Screen Pack Mesh (2 layers): #60-80
Extrusion parameters were found by extruding 3.2mm thick sheets at a haul off speed of 1368 mm/min and an output rate of 210 kg/hr. A polishing roll in a up stack wrap arrangement was used as well as a single screw with a 100mm diameter screw, a L/D ratio of 35/1, and a compression ratio of 3/1.
丙烯腈丁二烯苯乙烯ABS,ABS Hylac® EX18是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123 微信:13549213581 QQ:15397858
13549213581 肖生
|